Experienced a few days ago to buy millet wifi amplifier failed (see the card), think that the program is not feasible, even if a better route relay is not stronger, or consider other options
Insufficient amount of cheap price: Millet wifi amplifier 2 out of the box measured parental home 120m2, floor plan as follows, the house was renovated 12 years ago, then wifi is not universal, except that laptops almost no equipment needs wireless Internet access, then considered The entrance line is in bedroom B. The router and the computer are arranged directly into bedroom B, so the entire house is not equipped with network cables. . . When wifi became popular, the problem came. There was no signal in the bedroom C and the living room close to the balcony. Later the electricity cat was used. The bedroom B's home yyzn| Like 16 Comments 39 Collections 47 View Details The parents' home router was bought a few years ago. The TP's 2041N, only 2.4G, just took the opportunity to replace a dual-band Gigabit router.
Homegrown is R7000, do not want to buy the same, plus ASUS's firmware is strong, you can change the region (reported that China's power limit is 100, while the US power limit is 200), just try to solve problem
Select a good brand, they began to choose the model, the beginning to see the R7000's competitors AC68U, and later found AC66U B1 frequency is 1G, higher than the 68U, and the transfer rate of 1750 to 1900 is not much worse, parents need to access The equipment is not enough, 1750 is enough, other configurations are similar, in line with the principle of buying new and not buying the old, chose AC66U B1, Jingdong used a 100-20 coupon
ASUS RT-AC66U B1 AC dual frequency 1750M low radiation 1GHz dual-core processor USB3.0 three antenna wide coverage smart router 699 yuan upgrade version of AC66 Jingdong direct link to Wikipedia 
â–³ box has a hole, but there is a layer of film outside, it does not care about
â–³Unpacking, left power supply, right side routing body
â–³ remove the router, the bottom is the CD, manual, warranty card and the like, the bottom there is a network cable
â–³ The front is very concise, other routers are not the front of the layer of protective film can tear it, this Asus actually did not? ? ? The 8 LEDs are LAN1-LAN4, internet, 5G signal, 2.4G signal, and power supply.
â–³ front panel details, these lines are not printed, feel really uneven
â–³ The front right corner of the golden logo is very significant, although the gap is a bit large but the size of the gap is consistent, obsessive-compulsive disorder is very satisfied
â–³ As with the R7000 front USB3.0, it is said to solve the 5G signal interference problem, the parents home temporarily not used
â–³ is followed by the power connector, power switch, USB2.0, reset button, WAN, and 4 LANs, all of which are Gigabit ports.
â–³Side cooling hole
â–³ full bottom of the cooling holes and thick feet, heat dissipation should be good
â–³ Power looks very good, like this square power supply, and comes with a tie line, like
â–³ with a Category 5 network cable
â–³ is as large as the old route, but it is actually much smaller than the R7000.
experience feelings
â–³ Plug in the power supply and network cable, the power light, 2.4G and 5G are all bright blue light, normal work, because no account password is set, internet is red light
Aunt Zhang on the Huawei firmware a lot of settings, here only talk about setting it up with a mobile phone
â–³ The mobile phone is connected to the default SSID: ASUS_5G. It automatically pops up the setup page, sets the login password for the router, and sets the dial-up account password. It is very convenient, and you can also download the app operation.
â–³ Here can change the 2.4G and 5G SSID, it is worth mentioning that the change 2.4G, 5G will automatically change, the default is the name plus _5G, the password will be automatically modified to the same, do not repeat input, to the phone Operation brings convenience
â–³ After setting the internet indicator turns blue, you can access the external network
This time, it is mainly to solve the problem of house signals. Other advanced functions do not take care of them, and they are not used anyway. Let's review the floor plan first. The entrance line is in bedroom B. There is no embedded network cable in the whole house. Currently the route can only be placed in bedroom B or the power cat is placed in position A. When the old route is in bedroom B, the living room is near the balcony. There is no signal in the place and in the bedroom C; when the old route is in position A, the bedroom B only has a signal at the door, and there is no signal on the bed.
The following tests respectively route the 2.4G and 5G speeds of the new route on the ABC three positions in bedroom B and position A. The parent's home notebook 7 years ago was extremely slow, too lazy to boot, and the speed was completed with a mobile phone. The phone was an Apple 7
Velocity 1: The route in the bedroom B, 2.4G, B, the speed is good, A is a lot worse, C only measured once, the second time shows that the speed fails
Velocity 2: The route in the bedroom B, 5G, AB is good, C directly displays the speed failure
Velocity 3: Utilize the electricity cat to place the route in position A, 2.4G, ABC is not very good, can make do with
Speed ​​measurement 4: The use of power cats will be placed on the route A, 5G, ABC are better than 2.4G, the basic can be used normally, and the same speed as the original route of the original room
Summary: In terms of speed, test two B and test four A, mobile phones and routing in the same room, test two B has 70Mbps, test four A only 26Mbps, visible power cat signal attenuation, indicating my home this The circuit is not suitable for electricity cats. But in terms of wifi signals, routing in position A is the best coverage for the whole house. So if you really want the speed and want the signal, you can consider using the open line to connect the home line to the location A. Forget it first. . . Do not want to carry out major projects
In the end, the solution I chose was routing in bedroom B. Anyway, bedroom C was unoccupied. As long as AB had a signal, when bedroom C was live, it was temporarily expanded with WiFi amplifier.
The above test route setting is the default area, which is China, and later it changed the area to the U.S. and Australia again, but there is no obvious difference.
to sum upThe bottom is covered with cooling holes and the pads are thick to facilitate heat dissipation
Simple connection and friendly user interface
Wi-Fi coverage is indeed much better than the old route. At the beginning, it is thought that changing the area to adjust the power to solve the problem, the actual use of the default settings can be found
The volume is much smaller than the R7000, but now there is no brush Meilin just ASUS firmware there are plug-ins available, and brush Merlin more cool, saying that the R7000 this shipment is really stable, the original firmware, a total of 13 devices at home and a large number of simultaneous connection, After buying home for one year and two months, I haven’t restarted yet. It’s nothing to play. Later, I’m in a mood to toss my family’s home with ASUS.
Last but not least, the app's interface is cool
Surge arrester is also called over-votage protector and over-volage lmiter. t is connected im paralle to the front end of the protected couipmen,. Whichprolects other clectrical equipment from lightning over-voltage, operating over-voltage, and power frequency transient over-voltage impac.
Composite Arrester,Electrical Insulation Composites,Electrical Box Insulation Covers,Composite Line Post Insulator
Jilin Nengxing Electrical Equipment Co. Ltd. , https://www.nengxingelectric.com