People's life is getting faster and faster, more and more people don't want to waste time on housework, and then use small appliances such as sweeping robots to improve their lifestyle. So, will it be difficult to repair when the sweeping robot fails? What can I do? People's life is getting faster and faster, more and more people don't want to waste time on housework, and then use small appliances such as sweeping robots to improve their lifestyle. So, will it be difficult to repair when the sweeping robot fails? What can I do?
After the intelligent sweeping robot has been used for a long time, it will not be able to avoid some faults, but not all faults need to be repaired by someone. The following small series will take care of some minor faults, which we can solve at home.
First, the side brush does not turnThe side brush does not turn basically a false fault, and the probability of brushing the motor problem is also small. If there is a problem with the brush motor, an alarm sound will appear.
Solution, steps:
1. First judge whether the machine has power (by the power indicator light next to the AUTO mode button of the machine). If it is red or orange, then the earth treasure is definitely dead, please charge. Before charging, you need to turn on the switch at the bottom of the treasure. It is recommended that the customer keep on and do not need to close. If the bottom switch of the sweeping robot is turned off, it will not charge.
2. If the battery indicator light next to the AUTO mode button is green, then it is judged whether or not the return mode is excluded in the mode of returning to the charging stand, and the problem of the side brush itself should be judged. include:
a, the side brush screw does not tighten
b, the screw turns too tight, causing the screw to break
c. The screw turns too tightly, and the thin side of the side brush is split.
d. The problem of the side brush motor (can be judged by the rotation of the side brush) - when the sweeper is fully charged, remove the side brush, press the AUTO mode, turn the machine back, and press the outside of the wheel with your finger , see if the rotating shaft of the roller brush and the side brush can rotate normally. If it can be rotated, there is no problem with the side brush motor. If the roller brush can be rotated, the side brush shaft cannot work normally, and there is a problem with the brush motor.
Second, the host can not open the machine or chargeIf the machine is not charged, it means that it is not charged or not enough.
Solution, steps :
1. First judge whether the switch at the bottom of the machine is turned on, and charge it in the off state. The switch at the tail will also flash, but the power will not be charged. Therefore, please confirm that the bottom switch is turned on before charging. It is recommended that the machine be always on and do not need to be turned off. If the bottom switch of the machine is turned off, it will not charge.
2. Please make sure that the home is disconnected when charging.
3. Whether the machine is separated from the charging stand by a little bit during the charging process, or is not fully touched.
4. After the machine is fully charged, whether the power of the charging stand is unplugged, and the power of the machine body is not turned off after being pulled out, resulting in power loss.
5. Exclude the above method, it is recommended that the customer activate the battery. The activation method: manually take the machine back and charge it for 3 minutes, take it back for a few seconds, repeat this 3 times, and finally let the sweeping robot charge for 12 hours. Look at it for a few more days.
The machine generally sounds an alarm, mainly for the following reasons: 1. No electricity, 2 brushing, side brushing, winding of the hair inside the driving wheel 3. The machine is stuck in the dead corner 4. The machine does have problems.
Solution, steps:
1. First judge whether the machine has electricity, whether the power indicator light is red, if it is red, then there is no electricity, and the alarm sound is a reminder that it needs to return to charge.
2, judging the use time, if more than a few months, it is likely to have entanglement, check the side brush, drive wheel whether there is hair entanglement, remove the roller brush for cleaning.
3. Whether the machine can't come out in a relatively small range, please intervene manually.
4, especially important is the cleaning of the roller brush (must be cleaned down), to eliminate the above problems, the machine does have problems.
Fourth, the machine sweeps in a small areaSmall-scale cleaning of the machine is generally normal, and it is necessary to confirm the actual range of machine cleaning and the cleaning time.
Solution, steps:
1. Confirm how long the machine works. If it is a few minutes or 10 minutes, it is basically normal.
2. Confirm the scope of machine cleaning. If it is cleaned in a living room or a dozen flat places, it is normal. It is recommended to insist on daily use. After familiarizing with the situation at home, after 7-10 days, the coverage area will reach 95% or more. .
3. Please remove the dust box from the ground, wipe the dust sensor inside, and wipe the bottom sensor on the bottom of the machine.
5. The noise becomes louder when the machine is working.The reason why the sweeping robot works when the sound becomes loud may be: the side brush and the roller brush have foreign matter entangled.
Solution, steps:
1. After turning off the power switch, remove the dust box and clean the garbage, then turn the bottom of the machine up.
2, check and ensure that there is no clogging at the brush suction port
3. Check and clean the roller brush (including the hair winding at the bearings at both ends of the roller brush)
4, check and clean the side brush
Sixth, the ability to clean and vacuumThe reason for the decrease in cleaning ability may be that excessive dust accumulated in the filter cotton in the dust box cannot be removed. There is a entanglement at the roller or drive wheel.
Solution, steps:
1. After turning off the power switch, remove the dust box
2. Does the filter cotton in the dust box accumulate excessive dust and promptly removes and replaces it?
3, clean the brush suction port no clogging
4. Check if there is any dirt or objects around the drive wheel to make it work.
The above content is the glitch solution of the sweeping robot. Usually, when you encounter problems, you are eager to find after-sales. In the end, you don’t have to spend a lot of money. After understanding the above information, we can easily get the problem if we meet small problems at home. It can't be solved without looking for a sale.
NINGBO LOUD&CLEAR ELECTRONICS CO.,LIMITED , https://www.loudclearaudio.com